PrimoCache 3.0.2

January 18, 2021 - Software
PrimoCache 3.0.2

PrimoCache is a software caching solution that cooperates with system memory, solid-state drives (SSDs) and flash drives to accelerate relatively slow storage devices.

It transparently stores disk data into faster cache devices such as system memory and SSDs, so that future read requests for those data will be served directly from the cache and be faster. Thus access time will be reduced, showing a great improvement in the system reading performance.

Furthermore, PrimoCache is able to complete write requests very quickly by temporarily writing incoming data to fast cache devices first and writing them back to target disks later. In this manner, cache devices work as writing buffer, greatly improving the system writing performance and making the system able to handle heavy or stream write IOs.

What It Can Do

PrimoCache is powerful and flexible, and able to be easily adopted in a very broad application scenarios and fields. It can solve the problem of read/write performance bottlenecks in personal computers, workstations, and small to large servers. It can help persons who are enthusiastic to improve boot and load times, working performance, gaming experience, system responsiveness, etc. It can also help persons who want to reduce writes and wear on SSDs and extend their lifespan.

The following is a simple list of scenarios for which you may use PrimoCache, but not limited to these scenarios.

PrimoCache In Detail

PrimoCache implements a two-level caching architecture consisting of level-1 cache and level-2 cache. Level-1 cache, also called RAM cache, is composed of physical memory. Level-2 cache, also known as SSD cache, is a secondary cache which typically resides on a solid-state drive, a flash drive or other fast persistent storage device. Obviously level-1 cache runs much faster than level-2 cache, although it is usually much smaller. PrimoCache allows a single level cache configuration using either level-1 cache or level-2 cache, as well as a two-level cache configuration using both levels of cache.

Unlike level-1 cache which cannot keep cache contents on reboot, level-2 cache is able to retain its cache contents across computer reboots because of the persistent nature of storage devices. This avoids fetching often-accessed data again from slow disks each time computer boots up. Thus level-2 cache will remarkably reduce boot-up time and speed up applications for those computers which install mechanical hard disks.

PrimoCache also supports write-deferred caching mode, which executes write requests on the cache first and synchronizes data from the cache to the disk after custom delays. Therefore write requests can be responded and completed very fast, greatly improving the disk write performance.

In addition, PrimoCache implements the Unified Invisible Memory Management Interface (UIMMI), which can use Invisible Memory as level-1 cache. Invisible Memory, also known as Unmanaged Memory, usually exists on 32-bit desktop Windows where 4GB or more physical memory is installed. This feature helps to overcome the Windows limits on amount of system memory and fully utilize all installed physical memory.

PrimoCache fulfills an intelligent cache replacement algorithm which optimally determines cache blocks needed to be discarded to make room for new data when cache space is full. This cache algorithm combines two normal algorithms which are Least Frequently Used (LFU) and Least Recently Used (LRU), and provides a better cache hit ratio. It is self-tuning and requires no user-specified parameters.

PrimoCache allows multiple cache strategies and flexible configurations. It is implemented in Windows kernel level and is transparent to other applications. Therefore no application or system changes are required for this caching solution. With PrimoCache, you can easily setup caches for local disks and speed up your computers.

Why PrimoCache?

Why do we need PrimoCache since Windows has already implemented a file-system level cache?

For Windows PC

Support Windows 10, Windows 8.1/8, Windows 7, Vista and XP (all editions, 32/64-bit)

Version 3.0.2 (2017-12-21)

Remark: Original installer with cracked overwrite…. Restart before use…


PrimoCache Desktop Edition 3.0.2

(Cracked Silent Install Repack) x86



(Cracked Silent Install Repack) x64


10 thoughts on “PrimoCache 3.0.2


Can you add a new version?


    new version only have trial and need keep reset it…


Hey! Any news regarding the new version? Rubord has a trial period reset, can you do a RePack?


      I know about her and I ask. You have 4.0.1. Can you do 4.1.0?


        it was 4.1.0 i type wrong version


Do you have Server Edition? Thanks


      Oh! that’s quick! thank you! 🙂


Both versions (3.0.2 and 4.1.0) just show as registered and 365 days trial. But, after a several days, the program started to stop working.

Requires a reset every time it happens.

Leave a Reply